Authorized DealerGenerac Generator Service, Maintenance & Repair in Portland, Oregon
A standby generator earns its keep on the one night it has to start. We service, test, and repair home and commercial standby generators so that night goes the way it should — and our on-call line answers 24/7 when it doesn't.
- OR CCB #195783 · ELEC C818
- Licensed, bonded & insured
- 24/7 outage service

Paramount Electric Co. services and repairs Generac and other standby generators across the Portland metro. As a Generac Authorized Dealer, our annual maintenance covers oil and filter, a battery load test, a controller check, and a test run under load. We also diagnose failed starts and controller alerts, and our on-call line answers 24/7 during outages.
What's in an annual maintenance visit
A standby generator is an engine that sits idle most of its life, which is hard on engines. Our annual maintenance covers the items that decide whether it starts: an oil and filter change, a battery load test, a controller check for stored alerts and correct settings, and a test run under load to confirm it actually carries the building rather than just idling. We also look over the enclosure, connections, and fuel supply, and confirm the exercise schedule is set. Depending on run hours and the manufacturer's schedule, spark plugs and air filters are replaced at set intervals.
Why the generator won't start
The most common reason a standby generator fails to start is the battery. It sits on a charger for years and fails quietly, which is why a load test — not just a voltage reading — is part of every service. After the battery, the usual causes are a fuel supply problem (a closed valve, low propane, or gas pressure that drops under load), a stored fault on the controller that locked the unit out, low oil level, or a unit switched out of automatic mode after earlier work. If your generator cranks but won't run, runs and shuts down, or shows an alert on the controller, leave it in the state you found it, note the message, and call us.
Controller alerts and error codes
Modern standby generators report their own problems. The controller logs events like overcrank (it tried to start and couldn't), low oil pressure, high temperature, overspeed, low battery, and missed exercise cycles. Some alerts clear after service; others point to a part that needs replacing. Clearing a code without finding the cause just resets the clock on the same failure. We read the history, test the system the alert points to, and tell you what it means in plain terms before recommending a repair.
Common repairs
Most repairs we see are predictable wear items and outdoor exposure: batteries and battery chargers, starter and ignition components, voltage regulators, controller boards and wiring connections, fuel regulators, and rodent damage to wiring inside the enclosure. On the transfer-switch side we see worn contacts, control wiring faults, and switches that were never tested after installation. Repairs are quoted in writing before the work is done, so the decision to repair or replace is yours to make with a number in hand.
Commercial maintenance contracts
For clinics, care facilities, hotels, and other commercial buildings, we set up recurring generator maintenance with documentation: scheduled engine and battery service, controller and alarm checks, transfer-switch testing, and runs under load, logged so you can show the system was maintained and tested. The right interval and test regimen depend on the equipment and on what your occupancy and authority having jurisdiction require, and we build the schedule around that. Generator service can be folded into a broader electrical maintenance agreement for the building.
24/7 outage response
Generators fail at the worst time by definition — the failure shows up when the unit is finally asked to run. Our on-call line, (971) 471-7897, answers 24/7 for emergencies, including generators that don't start or don't transfer during an outage. During a regional storm, calls are triaged, and critical loads such as medical equipment and care facilities are prioritized. The best protection is still a service visit before storm season.
We service generators installed by others
You don't need to have bought the unit from us. We service and repair existing standby generators, and a first visit doubles as a condition check of the original installation — transfer switch rating, grounding and bonding, clearances, and gas supply. If we find something that was done wrong, we tell you what it is and what it would take to correct, and you decide.
Maintenance plans for homeowners
Homeowners who'd rather not track service dates can put the generator on a maintenance plan that includes the annual service alongside an electrical safety inspection of the home. Ask us about maintenance plans for homeowners when you request service and we'll walk you through the options.
Who We Do This Work For
Our Process, Step by Step
- Request serviceTell us the make, model, and what it's doing — an alert, a failed exercise, or simply due for service.
- Inspect & diagnoseWe check the unit, battery, controller history, fuel supply, and transfer switch.
- Quote before repairsMaintenance is done as scheduled; anything beyond it is quoted in writing before work proceeds.
- Service or repairParts and labor by licensed electricians familiar with the equipment.
- Test under loadWe run the generator under load and confirm the transfer sequence.
- ReportYou get a record of what was done and anything to watch.
Code & permits
Routine maintenance doesn't require a permit, but repairs that alter the installation — replacing a transfer switch, relocating the unit, or changing the wiring — do. For commercial systems classified as emergency or legally required standby, testing and maintenance intervals are set by the applicable code and the authority having jurisdiction; we document each visit so the record is there when it's asked for.
Who issues electrical permits in Oregon →Keep It Ready: Yearly Generator Maintenance, Built In
Plans start at $19/month with an annual electrical safety inspection and a labor discount on service and repairs. Ridge and Summit add yearly standby generator maintenance.
Generator Service, Maintenance & Repair — Questions We Hear
How often should a standby generator be serviced?
What does generator maintenance include?
Why won't my Generac generator start?
Do you repair generators you didn't install?
Do you offer emergency generator repair during an outage?
Do you offer a generator maintenance plan?
Does maintenance affect my generator's warranty?
Generator Service, Maintenance & Repair Work We Can Show You
Field Notes on Generator Service, Maintenance & Repair
Generator Service, Maintenance & Repair across the Portland metro
Working with a contractor for the first time? Start with Paramount Electric Co. — or see how we work with facility & property managers and general contractors.
See what clients say about working with Paramount — Read our Google reviews.
Schedule a Generator Assessment
Tell us about the home or building and what has to stay on in an outage. We'll walk the site, size the system from a load calculation, and return a fixed-price quote for the full scope — generator, transfer switch, gas and electrical, permit, and startup.
- Generac Authorized Dealer — sales, installation, and service
- Licensed electricians, OR CCB #195783 · ELEC C818
- Permits and inspection handled
- Power out right now? Call (971) 471-7897 — 24/7 outage service
Don't wait for the next outage
Schedule a generator assessment online, or call — our on-call line answers 24/7 for outage service.

