October 29, 2026 · 6 min read

How Much Electricity Does a Space Heater Use?

A typical portable space heater draws 1,500 watts on its high setting, which is 1.5 kilowatt-hours of electricity for every hour it runs. To get your cost, multiply the kilowatt-hours by the price per kWh on your utility bill. Just as important as the cost: 1,500 watts is about 12.5 amps, which is most of what a standard household circuit can safely carry.

Close-up of an electric space heater's heating elements glowing orange behind a wire guardResidential

How many watts does a space heater use?

Most plug-in space heaters sold for homes top out at 1,500 watts on high, with a low setting commonly around 750 to 900 watts. That ceiling is not a coincidence: it is roughly the most a heater can draw continuously from a standard 15-amp, 120-volt outlet.

The exact figure is printed on the heater's nameplate label, usually on the bottom or back. Use that number for your own math.

How do I calculate what my space heater costs to run?

The formula is watts, divided by 1,000, times hours, times your electricity rate.

Watts ÷ 1,000 gives kilowatts. A 1,500-watt heater is 1.5 kW. Multiply by the hours it runs to get kilowatt-hours: 1.5 kW for 8 hours is 12 kWh. Then multiply by the per-kWh price on your bill. If you run it 8 hours a day for a 30-day month, that is 360 kWh for that one heater.

Your rate is on your utility bill, shown per kWh. Rates differ by utility and plan and change over time, and some plans charge more at certain times of day, so use your own bill rather than a number from the internet. Whatever your rate is, 360 kWh is a meaningful addition to a monthly bill.

  • Find the wattage on the heater's nameplate
  • Divide by 1,000 to get kilowatts
  • Multiply by hours of use to get kWh
  • Multiply by your utility's price per kWh
  • A thermostat that cycles the heater off lowers the real total below the worst case

Are some space heaters more efficient than others?

Not in the way the marketing suggests. Electric resistance heat converts essentially all the electricity it draws into heat, whether the heater is ceramic, oil-filled, infrared, or a bare coil. A 1,500-watt heater of any type puts 1,500 watts of heat into the room.

What differs is how the heat is delivered and controlled. Oil-filled radiators heat slowly and evenly, fan-forced ceramic units warm a space quickly, and infrared heaters warm people and objects in front of them rather than the air. A good thermostat and a timer do more for your bill than the heating technology, because they reduce the hours the heater actually runs.

The genuinely more efficient option is a heat pump, which moves heat rather than making it and delivers several times more heat per kWh. If you are running space heaters daily to make a room livable, that is a sign the room's permanent heating deserves attention.

Why does my space heater trip the breaker?

Because it is using most of the circuit by itself. At 120 volts, 1,500 watts is 12.5 amps. A standard 15-amp circuit is only meant to carry 12 amps continuously, and a 20-amp circuit 16 amps. A heater on high therefore fills a 15-amp circuit completely, and anything else on that circuit, a vacuum, a hair dryer, a TV and a computer, pushes it over.

Remember that a circuit usually serves several outlets, often in more than one room. Two space heaters on the same circuit will trip it every time. So will one heater plus a microwave.

A breaker that trips under this load is doing its job. Do not replace it with a larger one: the breaker is sized to protect the wire in the wall, and a bigger breaker on the same wire lets the wire overheat instead.

What are the warning signs that a heater is stressing my wiring?

Space heaters run at full draw for hours, which exposes every weak point between the panel and the plug. Stop using the heater on that outlet and have it checked if you notice any of these.

  • The plug or the outlet cover is hot to the touch
  • The plug fits loosely or falls out of the receptacle
  • Discoloration or melting on the plug or outlet
  • A fishy or hot-plastic smell
  • Lights dimming noticeably when the heater cycles on
  • The breaker trips repeatedly

How do I use a space heater safely?

Plug it directly into a wall outlet. Extension cords and power strips are a leading cause of heater-related fires because most are not built to carry that load for hours. Keep it at least three feet from bedding, curtains, and furniture, set it on a hard level floor, and turn it off when you leave the room or go to sleep. Choose a model with tip-over and overheat shutoff.

In older homes, be more cautious. Worn receptacles, backstabbed connections, and aging wiring that have coped for decades with lamps and chargers can fail under a heater's sustained load.

When does it make sense to call an electrician?

If you rely on a space heater in the same spot every winter, a dedicated circuit for it removes the tripping and the strain on shared wiring. If outlets are warm, loose, or discolored, they should be replaced and the connections checked. And if you are heating a room this way because the house's system cannot keep up, we can install the circuit for a permanent solution such as a ductless heat pump or a hardwired wall heater, and confirm your panel has the capacity for it.

Common questions

How much electricity does a space heater use?
A typical space heater draws 1,500 watts on high, which is 1.5 kWh for each hour of operation. Run 8 hours a day, that is about 12 kWh daily. Multiply by your utility's per-kWh rate for the cost.
Is it cheaper to run a space heater than central heat?
It depends on your heating system and how much of the home you are heating. Warming one occupied room while turning down the whole-house thermostat can save energy; running several space heaters around the house usually does not, especially compared with a heat pump.
Can I plug a space heater into a power strip or extension cord?
No. Plug it directly into a wall outlet. Most cords and power strips are not rated for a heater's continuous load and can overheat.
Why does my breaker trip when I run a space heater?
A 1,500-watt heater draws about 12.5 amps, nearly the full continuous capacity of a 15-amp circuit. Any other load on the same circuit pushes it past the limit and the breaker trips, as it should.
Do I need a dedicated circuit for a space heater?
Not required for a portable heater, but if you use one regularly in the same location it is the reliable fix for nuisance tripping and overheated outlets.
Written by the licensed electricians at Paramount Electric Co. (OR CCB #195783 · ELEC C818) and reviewed by Maurice Greven, Project Manager / Supervisor, who holds Oregon supervising electrician license #4828S. Have a job this applies to? Call (971) 471-7897 or request service online.

Heater keeps tripping the breaker?

We can add a dedicated circuit, replace worn outlets, or check whether your panel has room for a permanent heating solution.