What Size Standby Generator Do I Need?
Most single-family homes need a standby generator between about 14 and 26 kW, and the right number comes from a load calculation of your actual appliances — not from square footage or the size of your electrical service. With load management, a 22–26 kW air-cooled unit can back up many whole homes, including ones with a 200-amp panel.
What size standby generator does a typical house need?
A typical single-family home needs roughly 14–26 kW. Essential-circuit coverage — heat, refrigeration, a well or sump pump, lights, and internet — often fits in the lower part of that range. Whole-home coverage with load management commonly lands at 22–26 kW. Large or all-electric homes can need more.
Those are typical ranges, not a prescription. The two things that move a home out of them are electric heat and multiple large 240-volt loads running at once: electric furnaces, electric tankless water heaters, big heat pumps with resistance backup, and EV chargers.
What size generator do I need for a 200-amp service?
A 200-amp service does not require a generator that can produce 200 amps. Service size is the maximum the home could draw; actual demand is far lower. Many 200-amp homes are well served by a 22–26 kW generator with a 200-amp service-rated automatic transfer switch and load management on the largest circuits.
For reference, 200 amps at 240 volts is 48 kW — a figure almost no home approaches in real use. The transfer switch is sized to the service so it can act as the main disconnect; the generator is sized to the load. Confusing those two is the most common reason people are sold an oversized unit.
How is a generator load calculation done?
A load calculation lists the loads you want backed up, takes each one's running wattage, adds the extra starting current that motors draw, and applies the demand factors the electrical code allows. The result is the capacity the generator needs to start and carry those loads together.
Motors are the detail that matters. A heat pump compressor, well pump, or refrigerator draws several times its running current for a moment at startup. A generator sized only to running load will stumble when the heat pump kicks on while the well pump is running. Where a home has utility interval data or we can measure demand, that real-world number is a useful check on the calculation.
- Heating: gas furnace blower, heat pump, or electric resistance
- Water heating: gas, heat pump, or electric
- Well pump and sump pump
- Refrigerators and freezers
- Range, oven, and dryer — gas or electric
- EV charger
- Medical equipment and home office
Can a smaller generator run my whole house?
Often, yes — with load management. Modules on the largest circuits hold those loads off for a short time when the generator nears capacity, then restore them automatically. The whole panel stays live, but the heat pump and the EV charger don't start at the same moment.
On a hillside home in West Linn, we used a 22 kW generator with a 200-amp automatic transfer switch and load management on the HVAC to back up the full home, heat pump included, without stepping up to a larger unit. Good load management is usually cheaper than extra kilowatts.
What happens if a generator is too small or too big?
An undersized generator overloads: voltage and frequency sag, breakers trip, or the unit shuts down to protect itself — typically right when a large motor starts. An oversized generator costs more to buy, install, and fuel, and engines that run lightly loaded for long periods don't run at their best.
Neither failure shows up on a mild test day. They show up during a multi-day winter outage with the heat running, which is why sizing is done on paper first.
Does fuel type change the size I need?
Slightly. Many air-cooled generators carry a somewhat lower output rating on natural gas than on propane, so the same model delivers a little less on a gas main. The load calculation should use the rating for the fuel you'll actually burn.
Fuel supply can also limit size in practice. A generator can only produce its rated power if the gas meter and piping can feed it at full load, so gas capacity is checked alongside the electrical sizing.
How do I get my home sized correctly?
Ask for a site assessment that includes a written load calculation. It should list the loads considered, state whether the design is whole-home, managed whole-home, or essential circuits, and name the generator and transfer switch that result.
Paramount Electric Co. is a Generac Authorized Dealer and licensed Oregon electrical contractor. We size from your actual loads, show you the whole-home and essential-circuit options side by side, and quote a fixed price for the one you choose.
Common questions
Is a 22 kW generator enough for a 200-amp panel?
Can I size a generator by square footage?
What size generator do I need for a well pump and heat?
Do commercial buildings size generators the same way?
Not sure what size you need?
Schedule a generator assessment and we'll run the load calculation on your actual home — no guessing from square footage.
